Dover Flexo Electronics is proud to be able to meet the often extreme specifications of our customers. In the case of the transducer roll pictured above, the extra long Tension Roll transducer will be used in a wide-web film converting application at a well-known plastics products manufacturer.
An idler roll with integrated tension transducers built into each end, the Tension Roll transducer is famous for its rugged build and long-lasting performance. It is the most reliable device of its kind in the converting and printing industries, while also being available on short lead times. Because Dover Flexo Electronics uses state-of-the-art roll production equipment, and has also recently increased its capabilities to machine raw stock, the company can meet demanding performance and delivery requirements.
For another recent Tension Roll Transducer special order, pictured above, it was a 75-inch plasma-coated roll on an 80-inch long shaft being used for a winding application in the healthcare industry.
An idler roll with integrated tension transducers built into each end, the Tension Roll transducer is famous for being extremely rugged and long-lasting. It is the most reliable device of its kind in the converting and printing industries, while also being available on short lead times. Because Dover Flexo Electronics uses state-of-the-art roll production equipment, and has also recently increased its capabilities to machine raw stock, the company can meet demanding specifications and delivery requirements.
Need your tension rolls to be longer or to have a specialty finish or covering, or be able to operate at high speed? We welcome the opportunity to meet your strictest requirements.
A dead-shaft idler roller with tension sensors built into each roll end, the Tension Roll® transducer is ideal for installation on original equipment or for retrofits since it arrives pre-assembled and ready-to-install between the facing sides of a machine frame. It can be inserted into an appropriate web path location, and an accurate web tension value can be displayed on a connected indicator or controller.
No assembly required.
With the TR transducer the engineering time required to size the unit to the machine frame prior to installation is significantly lower than when installing standard shaft-end load cells or tension transducers onto an idler roll.
Another advantage of the Tension Roll transducer over a conventional idler roll with transducers is that it requires only a single transducer cable to connect at one end of the roll. The transducer's connector cable never has to cross the machine.
For web presses and machines that run an extreme range of materials and tensions, the Tension Roll transducer can be mounted in a pair of DFE's model C shaft-end tension transducers . This allows one range of tensions to be measured by the Tension Roll's sensors, while a higher load range can be measured using the externally-mounted tension transducers. This feature is convenient in the rare cases that a machine's tension range exceeds the 100:1 maximum-to-minimum tension ratio of DFE's extended range option.
The Tension Roll transducer is available with three (3) standard roll materials including aluminum, steel or stainless steel. Special roll surface materials are available. The standard overload capacity on the largest unit is 3,000 lbs (13,300 N).
Roll face width is sized individually (from 6 inches [152mm] up to 120 inches [3.0 m] ) to fit almost any application requirement. Choose a roll diameter from 2.25 inches (57mm) up to 6 inches (152mm) standard, or another custom diameter to fit your application. Load ratings from 12 to 400 pounds (55 to 1800N).
Tension Roll Transducers Capabilities
Transducers and idler roll in one, easy-to-install unit
Fast, hassle-free installation--like any dead-shaft idler roll
Aluminum, steel or stainless steel rolls in many surface finishes
Now in Three frame sizes plus many custom variations
One electrical cable
Just specify your desired shaft length, load rating, roll diameter and any options or a special roll finish.
This is faster, easier and less expensive than installing a separate idler roller with 2 transducers (a.k.a load cells). Only one transducer cable is used, meaning there is no cable-crossing between machine frames. Aluminum, steel or stainless steel rolls are available in many surface finishes.
Note of interest: The TR Tension Roll® Transducer is also referred to by some of our customers as the Dover Roller, the Tension Roller and sometimes the Tension Measurement Roller. Any way you like it, this is the easiest way for printers and manufacturers to measure web tension on a press, converting line or coating line.
Do you need a Tension Roll transducer with multiple transducer segments across the roll face? DFE makes a custom Tension Roll, called a Segmented Tension Roll transducer that measures web tension at multiple positions across the roll face at increments you specify. Find out more here .